manualshive.com logo in svg

D-Link xStack DGS-3620-52P, Manual

The D-Link xStack DGS-3620-52P is a high-performance switch designed for efficient network management. To help users get started, a Quick Installation Manual is available for download, free of charge, from manualshive.com. This manual provides step-by-step instructions for a seamless setup process, ensuring optimal performance of this innovative product.

Share
Download
background image

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide 

326 

 

Example 

To disable the PIM-SSM debug function: 

DGS-3620-28SC:admin# no debug pim ssm 
Command: no debug pim ssm 
 
Success. 
 
DGS-3620-28SC:admin# 

 

20-70

 

debug ripng flag 

Description 

This command is used to enable or disable the RIPng debug flag. 

 

Format 

debug ripng flag [{interface | packet [all | rx | tx] | route} | all] state [enable | disable] 

 

Parameters 

interface

 - (Optional) Specifies the state of the RIPng interface debug. The default setting is 

disabled. 

packet

 - (Optional) Specifies which packets should be set with debug flags. 

all

 - Specifies to set all packets with debug flags. 

rx

 - Specifies to set inbound packets with debug flag. 

tx

 - Specifies to set outbound packets with debug flag. 

route

 - (Optional) Specifies the state of the RIPng route debug. The default setting is disabled. 

all

 - Specifies to set all debug flags. 

state

 - Specifies the designated flags state. 

enable

 - Specifies that the designated flags state will be enabled. 

disable

 - Specifies that the designated flags state will be disabled. 

 

Restrictions 

Only Administrator-level users can issue this command. (EI Mode Only Command) 

 

Example 

To enable the RIPng debug: 

DGS-3620-28SC:admin# debug ripng state enable 
Command: debug ripng state enable 
 
Success. 
 
DGS-3620-28SC:admin# 

 

After enabling RIPng on an interface, the following information may appear when the interface 
state changes. 

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for xStack DGS-3620-52P

D-Link DGS-1024D - Switch Quick Installation Manual preview
DGS-1024D - Switch
Brand: D-Link Pages: 16
D-Link DGS-1016D - Switch User Manual preview
DGS-1016D - Switch
Brand: D-Link Pages: 44
D-Link DES-6000 Series Firmware Update Manual preview
DES-6000 Series
Brand: D-Link Pages: 3
D-Link DES-5024 - Switch Application Notes preview
DES-5024 - Switch
Brand: D-Link Pages: 2
D-Link DES-3828 - xStack Switch - Stackable Datasheet preview
DES-3828 - xStack Switch - Stackable
Brand: D-Link Pages: 3
D-Link DES-3550 User Manual preview
DES-3550
Brand: D-Link Pages: 192
D-Link DES-3326 Configuration Manual preview
DES-3326
Brand: D-Link Pages: 9
D-Link DES-3226L User Manual preview
DES-3226L
Brand: D-Link Pages: 110
D-Link DES-1026G User Manual preview
DES-1026G
Brand: D-Link Pages: 10
D-Link DES-1008D Manual preview
DES-1008D
Brand: D-Link Pages: 17
D-Link DES-1005P Quick Install Manual preview
DES-1005P
Brand: D-Link Pages: 4
D-Link DGS-1210-28P Manual preview
DGS-1210-28P
Brand: D-Link Pages: 9
D-Link DES-1024D Brochure preview
DES-1024D
Brand: D-Link Pages: 4
D-Link DGS-105 - Switch Datasheet preview
DGS-105 - Switch
Brand: D-Link Pages: 4
D-Link DES-1024D Quick Install Manual preview
DES-1024D
Brand: D-Link Pages: 2
D-Link des-1016a Quick Install Manual preview
des-1016a
Brand: D-Link Pages: 2
Eaton Pow-R-Line SPX0361126 Maintenance Manual preview
Pow-R-Line SPX0361126
Brand: Eaton Pages: 584
UNICOM SmartGST-2600M Specifications preview
SmartGST-2600M
Brand: UNICOM Pages: 1

Brands by name

Popular brands

Load more brands