xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
416
Format
config erps raps_vlan <vlanid> [state [enable | disable] | ring_mel <value 0-7> | ring_port
[west [<port> | virtual_channel] | east [<port> | virtual_channel]] | rpl_port [west | east | none]
| rpl_owner [enable | disable] | protected_vlan [add | delete] vlanid <vidlist> | sub_ring
raps_vlan <vlanid> tc_propagation state [enable | disable] | [add |delete] sub_ring raps_vlan
<vlanid> | revertive [enable | disable] | timer {holdoff_time <millisecond 0-10000> |
guard_time <millisecond 10-2000> | wtr_time <min 5-12>}(1)]
Parameters
<vlanid>
- The VLAN ID associated with the R-APS VLAN.
state
- Specifies the ERPS R-APS VLAN state.
enable
- Specifies that the ERPS R-APS VLAN state will be enabled.
disable
- Specifies that the ERPS R-APS VLAN state will be disabled.
ring_mel
- Specify the ring MEL of the R-APS function. The default ring MEL is 1.
<value 0-7>
- Specify a value between 0 and 7.
ring_port
- Specify a port participating in the ERPS ring.
west
- Specify the port as the west ring port.
<port>
- Specify a port.
virtual_channel
- Specify the port as a west port on the virtual channel.
east
- Specify the port as the east ring port.
<port>
- Specify a port.
virtual_channel
- Specify the port as an east port on the virtual channel.
rpl_port
- By default, the node has no RPL port.
west
- Specify the west ring port as the RPL port.
east
- Specify the east ring port as the RPL port.
none
- No RPL port on this node.
rpl_owner
- By default, the RPS owner is disabled.
enable
- Specify the device as an RPL owner node.
disable
- This node is not an RPL owner.
protected_vlan
- Specify VLANs that are protected by the ERPS function. The R-APS VLAN
cannot be the protected VLAN. The protected VLAN can be one that has already been
created, or it can be used for a VLAN that has not yet been created.
add
- Add VLANs to the protected VLAN group
delete
- Delete VLANs from the protected VLAN group.
vlanid
- Specify a VLAN ID list.
<vidlist>
- Specify a range of VLAN IDs.
sub_ring
- Specifies the sub-ring configuration.
raps_vlan
- Specify the R-APS VLAN.
<vlanid>
- Enter the R-APS VLAN ID used here.
tc_propagation
- Specifies to configure the state of the topology change propagation for
the sub-ring.
state
- Specifies the propagation state of the topology change for the sub-ring.
enable
- Enable the propagation state of the topology change for the sub-ring.
disable
- Disable the propagation state of the topology change for the sub-ring.
add
- Specifies the add a topology change propagation rule.
sub_ring
- Specifies the sub-ring configuration information.
raps_vlan
- Specify the R-APS VLAN
<vlanid>
- Enter the R-APS VLAN ID used here.
delete
- Specifies the delete a topology change propagation rule.
sub_ring
- Specifies the sub-ring configuration information.
raps_vlan
- Specify the R-APS VLAN.
<vlanid>
- Enter the R-APS VLAN ID used here.
revertive
- Specifies the revertive mode state.
enable
- Specifies that the revertive mode will be enabled.
disable
- Specifies that the revertive mode will be disabled.
timer
- Configure the ERPS timers for a specific R-APS VLAN.
