manualshive.com logo in svg

D-Link xStack DGS-3620-52P, Manual, Page: 286 / 1170

Share
Download
D-Link xStack DGS-3620-52P Manual Download Page 286

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide 

281 

 

DGS-3620-28SC:admin# debug ospf lsa all state enable 
Command: debug ospf lsa all state enable 
 
Success. 
 
DGS-3620-28SC:admin# 

 

To enable all OSPF packet debug flags: 

DGS-3620-28SC:admin# debug ospf packet all state enable 
Command: debug ospf packet all state enable 
 
Success. 
 
DGS-3620-28SC:admin# 

 

To enable OSPF retransmission debug flag: 

DGS-3620-28SC:admin# debug ospf retransmission state enable 
Command: debug ospf retransmission state enable 
 
Success. 
 
DGS-3620-28SC:admin# 

 

To enable all OSPF SPF debug flags: 

DGS-3620-28SC:admin# debug ospf spf all state enable 
Command: debug ospf spf all state enable 
 
Success. 
 
DGS-3620-28SC:admin# 

 

20-16

 

debug ospf clear counter 

Description 

This command is used to reset the OSPF statistic counters. 

 

Format 

debug ospf clear counter {packet | neighbor | spf} 

 

Parameters 

packet

 - (Optional) Specifies to reset the OSPF packet counter. 

neighbor

 - (Optional) Specifies to reset the OSPF neighbor event counter. 

spf

 - (Optional) Specifies to reset the OSPF SPF event counter. 

If the parameter is not specified, all OSPF counters will be cleared. 

 

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments