manualshive.com logo in svg

D-Link xStack DGS-3620-52P, Manual

The D-Link xStack DGS-3620-52P is a high-performance switch designed for efficient network management. To help users get started, a Quick Installation Manual is available for download, free of charge, from manualshive.com. This manual provides step-by-step instructions for a seamless setup process, ensuring optimal performance of this innovative product.

Share
Download
background image

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide 

279 

 

 

20-14

 

debug stp state 

Description 

This command is used to enable or disable the STP debug state. 

 

Format 

debug stp state [enable | disable] 

 

Parameters 

state

 - Specifies the STP debug state. 

enable

 - Enable the STP debug state. 

disable

 - Disable the STP debug state. 

 

Restrictions 

Only Administrator level users can issue this command. 

 

Example 

To configure the STP debug state to enable, and then disable the STP debug state: 

DGS-3620-28SC:admin# debug stp state enable 
Command: debug stp state enable 
 
Success. 
 
DGS-3620-28SC:admin# debug stp state disable 
Command: debug stp state disable 
 
Success. 
 
DGS-3620-28SC:admin# 

 

20-15

 

debug ospf 

Description 

This command is used to enable or disable OSPF debug flags. 

 

Format 

debug ospf [neighbor_state_change | interface_state_change {dr_bdr_selection} | lsa {all | 
originating | installing | receiving | flooding} (1) | packet {all | receiving | sending} (1) | 
retransmission | spf {all | intra | inter | extern} (1) | timer | virtual_link | route | redistribution] 
state [enable | disable] 

 

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for xStack DGS-3620-52P

D-Link xStack User Manual preview
xStack
Brand: D-Link Pages: 357
IBM RackSwitch G8264 Product Manual preview
RackSwitch G8264
Brand: IBM Pages: 20
IBM Flex System FC3171 Installation And User Manual preview
Flex System FC3171
Brand: IBM Pages: 64
C&H Technologies M221 Specifications preview
M221
Brand: C&H Technologies Pages: 1
D-Box G3 Installation Manual preview
G3
Brand: D-Box Pages: 31
B&K HD6 Product Manual preview
HD6
Brand: B&K Pages: 2
B&B Electronics 232BSS4 Manual preview
232BSS4
Brand: B&B Electronics Pages: 45
Nectarine Health Satellite Manual preview
Satellite
Brand: Nectarine Health Pages: 9
6TL YAV904X8 Manual preview
YAV904X8
Brand: 6TL Pages: 25
Intermatic T1906 Supplementary Manual preview
T1906
Brand: Intermatic Pages: 1
ATEN CN8000 KVM on the NET Quick Start Manual preview
CN8000 KVM on the NET
Brand: ATEN Pages: 2
Gembird UHB-U3P7P-01 User Manual preview
UHB-U3P7P-01
Brand: Gembird Pages: 2
Western Telematic IPS-800CE-D16, IPS-1600CE-D16 User Manual preview
IPS-800CE-D16, IPS-1600CE-D16
Brand: Western Telematic Pages: 58
Black Box ServSwitch KV1510A User Manual preview
ServSwitch KV1510A
Brand: Black Box Pages: 16
SMC Networks ZSE1 Series User Manual preview
ZSE1 Series
Brand: SMC Networks Pages: 6
Watt Stopper WI-200 Installation Instructions preview
WI-200
Brand: Watt Stopper Pages: 2
Steren FASTHOME 550-030 Installation Manual preview
FASTHOME 550-030
Brand: Steren Pages: 4
Witura WT-1673 User Manual preview
WT-1673
Brand: Witura Pages: 12

Brands by name

Popular brands

Load more brands