manualshive.com logo in svg

D-Link xStack DGS-3620-52P, Manual

The D-Link xStack DGS-3620-52P is a high-performance switch designed for efficient network management. To help users get started, a Quick Installation Manual is available for download, free of charge, from manualshive.com. This manual provides step-by-step instructions for a seamless setup process, ensuring optimal performance of this innovative product.

Share
Download
background image

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide 

201 

 

 

Example 

This is an example of configuring the BGP aggregate next hop check: 

DGS-3620-28SC:admin# config bgp aggregate_next_hop_check enable 
Command: config bgp aggregate_next_hop_check enable 
 
Success. 
 
DGS-3620-28SC:admin#  

 

12-55

 

config bgp fast_external_fallover 

Description 

This command configures a Border Gateway Protocol (BGP) routing process to immediately reset 
its external BGP peer sessions if the link used to reach these peers goes down, 

 

Format 

config bgp fast_external_fallover [enable | disable] 

 

Parameters 

enable

 - To enable BGP fast external fallover flag. Default is enabled. 

disable

 - To disable BGP fast external fallover. 

 

Restrictions 

Only Administrator, Operator and Power-User level users can issue this command. (EI Mode Only 
Command) 

 

Example 

This example disables BGP fast external fallver: 

DGS-3620-28SC:admin#  config bgp fast_external_fallover disable 
Command:  config bgp fast_external_fallover disable 
 
Success. 
 
DGS-3620-28SC:admin#  

 

12-56

 

config bgp neighbor maximum_prefix 

Description 

This command is used to configure the BGP neighbor maximum prefix. 

 

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for xStack DGS-3620-52P

Keithley 707 Quick Reference Manual preview
707
Brand: Keithley Pages: 66
D-Link SmartPro DGS-1500-20 Reference Manual preview
SmartPro DGS-1500-20
Brand: D-Link Pages: 113
D-Link xStack DGS-3120 Series Cli Reference Manual preview
xStack DGS-3120 Series
Brand: D-Link Pages: 1150
Eaton COOPER POWER SERIES Maintenance Instructions Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 32
Keithley 2750 User Manual preview
2750
Brand: Keithley Pages: 452
Magnetrol C29 Installation And Operating Manual preview
C29
Brand: Magnetrol Pages: 24
Xenteq PTS Series Instruction Manual preview
PTS Series
Brand: Xenteq Pages: 22
3Com OfficeConnect 5 Datasheet preview
OfficeConnect 5
Brand: 3Com Pages: 2
3Com OfficeConnect 3C1670500C User Manual preview
OfficeConnect 3C1670500C
Brand: 3Com Pages: 18
Thetford Marine TECMA Silence Marine Owner'S Manual preview
TECMA Silence Marine
Brand: Thetford Marine Pages: 9
Greengate VNLW-P-1001-MV-N-V Installation Instructions preview
VNLW-P-1001-MV-N-V
Brand: Greengate Pages: 2
Key Digital HD Flash 4 KD-SW4x1 Operating Instructions Manual preview
HD Flash 4 KD-SW4x1
Brand: Key Digital Pages: 12
CYP CDPS-UA6H2HFS Operation Manual preview
CDPS-UA6H2HFS
Brand: CYP Pages: 32
UniFi USW-Flex-Mini Quick Start Manual preview
USW-Flex-Mini
Brand: UniFi Pages: 8
ATEN Master View CS-74A User Manual preview
Master View CS-74A
Brand: ATEN Pages: 16
Minicom Smart 4 User Manual preview
Smart 4
Brand: Minicom Pages: 16
Pilz 506401 Operating Manual preview
506401
Brand: Pilz Pages: 20
Zektor HD800-V2 User Manual preview
HD800-V2
Brand: Zektor Pages: 41

Brands by name

Popular brands

Load more brands