D-Link xStack DGS-3620-52P Manual Download Page 1048 | Manualshive

Page: 1048 / 1170

background image

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide

1043

current user working directory will be searched first, followed by the environment paths.

<path_filename 64>

-

Specify the path name of the RCP server.

rcp:

-

Specify the path name on the RCP server.

<string 128>

- Specify the path name on the RCP server. Syntax: rcp:

username@ipaddr/directory/filename. Example for full path:
[email protected]/home/user_name/desxxxx.had. Example for relative path:
[email protected]./desxxxx.had. Note: No spaces are allowed in the whole <string>.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example

To upload the log from the device to an RCP server:

DGS-3620-28SC:admin#upload log_toRCP username rcp_user 172.18.212.104 dest_file
/home/DGS-3620.log
Command: upload log_toRCP username rcp_user 172.18.212.104 dest_file /home/DGS-
3620.log

Connecting to server................... Done.
Upload log............................. Done.

Success.

To upload log from the device to an RCP server using an RCP string:

DGS-3620-28SC:admin#upload log_toRCP rcp: [email protected]/home/DGS-3620.log
Command: upload log_toRCP rcp: [email protected]/home/DGS-3620.log

Connecting to server................... Done.
Upload log............................. Done.

Success.

DGS-3620-28SC:admin#

103-9

config firmware image

Description

This command is used to configure firmware as a boot-up image.

Format

config firmware image {unit <unit_id>} <pathname> boot_up

Parameters

unit

– (Optional) Specifies the unit ID used for this configuration.

<unit_id>

- Enter the unit ID used for this configuration here.

«
...
1046
1047
1048
1049
1050
...
»

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for xStack DGS-3620-52P

Brand: Omega Engineering Pages: 3

Matrix-PRO HD-SDI

Brand: Barco Pages: 2

SmartCell 6A000

Brand: Cabletron Systems Pages: 114

Brand: Cabletron Systems Pages: 62

CyberSWITCH CSX150

Brand: Cabletron Systems Pages: 49

Cabletron CyberSWITCH CSX5500

Brand: Cabletron Systems Pages: 729

Brand: vantiva Pages: 58

DMS-1250 Series

Brand: D-Link Pages: 38

Elinx EIR418-2SFP-T

Brand: B&B Electronics Pages: 25

Brand: CIS Pages: 3

Brand: Endress+Hauser Pages: 25

Brand: Fairchild Pages: 19

TurboIron 24X series

Brand: Brocade Communications Systems Pages: 82

Brand: Extron electronics Pages: 3

Guard Master 440N-Z2NRS1A

Brand: Allen-Bradley Pages: 4

FlexFabric 5940 Series

Brand: Hewlett Packard Enterprise Pages: 123

Enova DGX 100 Series

Brand: AMX Pages: 2

Brand: Emulex Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands