D-Link xStack DGS-3620-52P Manual Download Page 277

Page: 277 / 1170

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide

272

Example

To set the switch to not need a reboot when a fatal error occurs:

DGS-3620-28SC:admin# debug config error_reboot disable
Command: debug config error_reboot disable

Success.

DGS-3620-28SC:admin#

20-7

debug config state

Description

Use the command to set the state of the debug.

Format

debug config state [enable | disable]

Parameters

enable

- Enable the debug state.

disable

- Disable the debug state.

Restrictions

Only Administrator level users can issue this command.

Example

To set the debug state to disabled:

DGS-3620-28SC:admin# debug config state disable
Command: debug config state disable

Success.

DGS-3620-28SC:admin#

20-8

debug show error_reboot state

Description

Use the command to show the error reboot status.

Format

debug show error_reboot state

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for xStack DGS-3620-52P

Reviews:

D-Link xStack DGS-3620-52P, Manual, Page: 277 / 1170

Search results

Summary of Contents for xStack DGS-3620-52P

Reviews: