manualshive.com logo in svg

D-Link xStack DGS-3620-52P, Manual

The D-Link xStack DGS-3620-52P is a high-performance switch designed for efficient network management. To help users get started, a Quick Installation Manual is available for download, free of charge, from manualshive.com. This manual provides step-by-step instructions for a seamless setup process, ensuring optimal performance of this innovative product.

Share
Download
background image

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide 

199 

 

all

 - Enable or disable the sending of both the peer idle and established trap. This default value is 

disabled. 

enable

 - Specifies that the trap feature will be enabled. 

disable

 - Specifies that the trap feature will be disabled. 

 

Restrictions 

Only Administrator, Operator and Power-User level users can issue this command. (EI Mode Only 
Command) 

 

Example 

This example disables the BGP peer idle trap state: 

DGS-3620-28SC:admin#  config bgp trap peer_idle disable 
Command:  config bgp trap peer_idle disable 
 
Success. 
 
DGS-3620-28SC:admin#  

 

12-52

 

show bgp trap_state 

Description 

This command is used to show the BGP trap state. 

 

Format 

show bgp trap_state 

 

Parameters 

None. 

 

Restrictions 

None. (EI Mode Only Command) 

 

Example 

This example displays the BGP trap state: 

DGS-3620-28SC:admin#  show bgp trap_state 
Command:  show bgp trap_state 
 
BGP Trap State         : 
BGP Peer Established   : Enabled 
BGP Peer Idle          : Enabled 
 
DGS-3620-28SC:admin#  

 

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for xStack DGS-3620-52P

Keithley 707 Quick Reference Manual preview
707
Brand: Keithley Pages: 66
DANLERS CESF PIR Installation Notes preview
CESF PIR
Brand: DANLERS Pages: 2
Datavideo SE-3000 Instruction Manual preview
SE-3000
Brand: Datavideo Pages: 58
SIMON RWA HE 083 Brief Instruction preview
HE 083
Brand: SIMON RWA Pages: 3
Quintum Tenor AXE1600 Specifications preview
Tenor AXE1600
Brand: Quintum Pages: 2
Baxall DVS24 Installation And Operating Instructions Manual preview
DVS24
Brand: Baxall Pages: 33
LevelOne Infinity IES-1881 Quick Installation Manual preview
Infinity IES-1881
Brand: LevelOne Pages: 2
SMART Hub VE220 Installation And User Manual preview
Hub VE220
Brand: SMART Pages: 46
NBase Communications NH2001M Installation And User Manual preview
NH2001M
Brand: NBase Communications Pages: 72
Cabletron Systems 6H122-08 User Manual preview
6H122-08
Brand: Cabletron Systems Pages: 170
Lantech IPES-5222T Series User Manual preview
IPES-5222T Series
Brand: Lantech Pages: 30
Lantech IES-5216DF User Manual preview
IES-5216DF
Brand: Lantech Pages: 30
Bühler technologies Nivotemp NT-EL Installation And Operation Instructions Manual preview
Nivotemp NT-EL
Brand: Bühler technologies Pages: 20
Optex OAM-DUAL T Operation Manual preview
OAM-DUAL T
Brand: Optex Pages: 2
Hall Research Technologies KVMC-UH-8 User Manual preview
KVMC-UH-8
Brand: Hall Research Technologies Pages: 9
ALFAtron ALF- WUK3A Manual preview
ALF- WUK3A
Brand: ALFAtron Pages: 15
Clas Ohlson EMT1700P Manual preview
EMT1700P
Brand: Clas Ohlson Pages: 5
Ross OpenGear DSS-8224 User Manual preview
OpenGear DSS-8224
Brand: Ross Pages: 47

Brands by name

Popular brands

Load more brands