D-Link DGS-1100-16/ME Reference Manual Download Page 132

Page: 132 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

LLDP COMMANDS

The LLDP commands in the Command Line Interface (CLI) are listed (along with the appropriate

parameters) in the following table.

Command

Parameter

enable lldp

disable lldp

show lldp

show lldp remote_ports

config lldp

notification [enable | disable]

Each command is listed in detail, as follows:

enable lldp

Purpose

To enable LLDP on the switch.

Syntax

enable lldp

Description

The

enable

lldp

command enables the Link Layer Discovery

Protocol (LLDP) on the switch.

Parameters

None

Restrictions

Only administrator-level users can issue this command.

Example usage:

To enable LLDP on the switch:

DGS-1100-24P/ME:admin#enable lldp
Command: enable lldp

Success.

DGS-1100-24P/ME:admin#

disable lldp

Purpose

To disable LLDP on the switch.

Syntax

disable lldp

Description

The

disable lldp

command disables the Link Layer Discovery

Protocol (LLDP) on the switch.

Parameters

None.

123

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands