D-Link DGS-1100-16/ME Reference Manual Download Page 165

Page: 165 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

show voice_vlan global

Purpose

Shows the Surveillance VLAN global information

Syntax

show surveillance_vlan global

Description

This command is used to show the Surveillance VLAN information.

Parameters

None.

Restrictions

None.

Example usage:

To show voice vlan global information:

DGS-1100-24P/ME:admin#show voice_vlan global
Command : show voice_vlan global

Voice VLAN State  : Enabled
VLAN ID         : VLAN3
VLAN Name         : VLAN0003
Priority             : 7
Aging Time       : 600 minutes

DGS-1100-24P/ME:admin#

show voice_vlan oui

Purpose

Shows the Voice VLAN oui information

Syntax

show voice_vlan oui

Description

This command is used to show the Voice VLAN oui information.

Parameters

None.

Restrictions

None.

Example usage:

156

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands