D-Link DGS-1100-16/ME Reference Manual Download Page 146

Page: 146 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

D-LINK DISCOVERY PROTOCOL COMMANDS

The D-link Discovery Protocol (DDP) commands in the Command Line Interface (CLI) are listed (along

with the appropriate parameters) in the following table.

Command

Parameter

enable ddp

disable ddp

config ddp report_time [30 | 60 | 90 | 120 | never]
show ddp

Each command is listed in detail, as follows:

enable ddp

Purpose

To enable DDP support of the switch.

Syntax

enable ddp

Description

The

enable ddp

command enables DDP support of the switch.

Parameters

None.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To enable DDP support

DGS-1100-24P/ME:admin#enable ddp
Command : enable ddp

Success.

DGS-1100-24P/ME:admin#

disable ddp

Purpose

To disable DDP support of the switch.

Syntax

disable ddp

Description

The

disable ddp

command disables DDP support of the switch.

Parameters

None.

Restrictions

Only administrator-level users can issue this command.

137

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands