D-Link DGS-1100-16/ME Reference Manual Download Page 98

Page: 98 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

IGMP SNOOPING COMMANDS

The Switch supports IGMPv1-, IGMPv2-, and IGMPv3 awareness (excluded IGMPv3 source-filtering)

snooping.
The IGMP Snooping commands in the Command Line Interface (CLI) are listed (along with the

appropriate parameters) in the following table.

Command

Parameter

enable igmp_snooping

disable igmp_snooping

show igmp_snooping

[vlan_name <vlan_name 8> | vlanid<vidlist 1-4094> | all]

config igmp_snooping

[vlan_name <vlan_name 8> | vlanid <vidlist 1-4094> | all] {fast_leave [enable |

disable] | state [enable | disable]}(1)

config igmp_snooping

querier

[vlan_name <vlan_name 8> | vlanid <vidlist 1-4094> | all] state [enable | disable]

create igmp_snooping

static_group

[vlan_name<vlan_name 8> | vlanid < vidlist 1-4094> ] <ipaddr>

config igmp_snooping

static_group

[vlan_name <vlan_name 8> | vlanid < vidlist 1-4094> ] < ipaddr > [ add | delete]

delete igmp_snooping

static_group

[vlan_name<vlan_name 8> | vlanid < vidlist 1-4094> ] <ipaddr>

create igmp_snooping

multicast_vlan

<vlan_name 8> <vlanid 2-4094>

config igmp_snooping

multicast_vlan

<vlan_name 8> { action [add | delete] [member_port <portlist> | source_port

<portlist> | tag_member_port <portlist >] |state [enable | disable] |

replace_source_ip <ipaddr> } (1)

delete igmp_snooping

multicast_vlan

[name <vlan_name 8>| all]

config igmp_snooping

multicast_vlan_group

<vlan_name 8> [add | delete] ipv4_range <mcast_address_range>

enable igmp_snooping

multicast_vlan

disable igmp_snooping

multicast_vlan

show igmp_snooping

multicast_vlan

{name <vlan_name 8>}

show igmp_snooping

multicast_vlan_group

{name <vlan_name 8>}

show igmp_snooping

group

[all | [vlan_name <vlan_name 8> | vlanid <vidlist 1-4094> | ports <portlist>]

{ipaddress<ipaddr>}]

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands