D-Link DGS-1100-16/ME Reference Manual Download Page 87

Page: 87 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

VLAN COMMANDS

The VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate

parameters) in the following table.

Command

Parameter

create vlan

[name <vlan_name 8> tag<vlanid 2-4094> | vlanid <vidlist 2-4094>]

delete vlan

[name <vlan_name 8> | vlanid <vidlist 2-4094>]

config vlan

[name <vlan_name 8> [add [tagged | untagged] | delete ] <portlist> | vlanid

<vidlist 1-4094>] [[add [tagged | untagged] | delete ] <portlist> | name

<vlan_name 8>]]

show vlan

{name <vlan_name 8> | vlanid <vidlist 1-4094> | ports <portlist>}

enable asymmetric_

vlan

disable

asymmetric_vlan

show asymmetric_vlan
enable

management_vlan

disable

management_vlan

config

management_vlan

vlanid <vlanid 1-4094>

show

management_vlan

config port_vlan

show port_vlan

{port <portlist>}

enable pvid

auto_assign

disable pvid

auto_assign

show pvid auto_assign

Each command is listed in detail, as follows:

create vlan

Purpose

To create a VLAN on the Switch.

Syntax

create vlan [name <vlan_name 8> tag<vlanid 2-4094> | vlanid

<vidlist 2-4094>]

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands