D-Link DGS-1100-16/ME Reference Manual Download Page 133

Page: 133 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

Restrictions

Only administrator-level users can issue this command.

Example usage:

To disable LLDP on the switch:

DGS-1100-24P/ME:admin#disable lldp
Command: disable lldp

Success.

DGS-1100-24P/ME:admin#

show lldp

Purpose

To display the

Link Layer Discovery Protocol

(LLDP) on the switch.

Syntax

show lldp

Description

The

show lldp

displays the LLDP configuration on the switch.

Parameters

None.

Restrictions

None.

Example usage:

To show LLDP settings:

DGS-1100-24P/ME:admin#show lldp

Command : show lldp

LLDP State : Disabled

LLDP Trap State : Disabled

DGS-1100-24P/ME:admin#

show lldp remote_ports

Purpose

To display information regarding the neighboring devices discovered

using LLDP.

Syntax

show lldp remote_ports

Description

The

show lldp remote_ports command

displays the information

regarding neighboring devices.

Parameters

None.

Restrictions

None.

Example usage:

To show the information for remote ports:

124

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands