D-Link DGS-1100-16/ME Reference Manual Download Page 112

Page: 112 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

Command

Parameter

static_group

Each command is listed in detail, as follows:

enable mld_snooping

Purpose

To enable MLD snooping on the Switch.

Syntax

enable mld snooping

Description

The

enable mld snooping

command enables MLD snooping on the

Switch.
If IGMP snooping is also enabled, this operation may possibly fail

due to the total number of group entrys exceeding the limitation of

group table.

Parameters

None

Restrictions

Only administrator-level users can issue this command.

Example usage:

To enable the MLD snooping:

DGS-1100-24P/ME:admin#enable mld_snooping
Command : enable mld_snooping

Success.

DGS-1100-24P/ME:admin#

disable mld_snooping

Purpose

To disable MLD snooping on the Switch.

Syntax

disable mld snooping

Description

The

disable mld snooping

command disables MLD snooping on

the Switch. Disabling MLD snooping allows all MLD and IP multicast

traffic to flood within a given IP interface.

Parameters

None

Restrictions

Only administrator-level users can issue this command.

Example usage:

To disable the MLD snooping:

DGS-1100-24P/ME:admin#disable mld_snooping
Command : disable mld_snooping

Success.

DGS-1100-24P/ME:admin#

103

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands