D-Link DGS-1100-16/ME Reference Manual Download Page 70

Page: 70 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

To create a unicast MAC FDB entry:

DGS-1100-24P/ME:admin#create fdb vlanid 1 22-ff-ff-ff-ff-ff port

2
Command : create fdb vlanid 1 22-ff-ff-ff-ff-ff port 2

Success.

DGS-1100-24P/ME:admin#

create multicast_fdb

Purpose

To create a static entry in the multicast MAC address forwarding

table (database).

Syntax

create multicast_fdb name <vlan_name 8> <macaddr>

Description

The

create multicast_fdb

command creates a static entry in the

multicast MAC address forwarding table (database).

Parameters

name <vlan_name 8>

− The name of the VLAN on which the MAC

address resides.

<macaddr>

− The MAC address to be added to the forwarding table.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To create multicast MAC forwarding:

DGS-1100-24P/ME:admin#create multicast_fdb name VLAN0001

ff-ff-ff-ff-ff-ff
Command : create multicast_fdb name VLAN0001 ff-ff-ff-ff-ff-ff

Success.

DGS-1100-24P/ME:admin#

config multicast_fdb

Purpose

To configure the Switch’s multicast MAC address forwarding

database.

Syntax

config multicast_fdb name <vlan_name 8> <macaddr> [add |

delete] <portlist>

Description

The

config multicast_fdb

command configures the multicast MAC

address forwarding table.

Parameters

<vlan_name 8>

− The name of the VLAN on which the MAC

address resides.

<macaddr>

− The MAC address to be

configured to the forwarding

table.

add

− Specifies that the MAC address is to be added to the

forwarding table. Delete will remove the MAC address from the

forwarding table.

delete

− Specifies that the MAC address is to be removed from the

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands