D-Link DGS-1100-16/ME Reference Manual Download Page 179

Page: 179 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

APPENDIX B - TECHNICAL SPECIFICATIONS

Hardware Specifications
Key Components /

Performance

Switching Capacity:

- DGS-1100-16/ME: 32Gbps

- DGS-1100-18/ME: 36Gbps
- DGS-1100-24/ME: 48Gbps
- DGS-1100-26/ME : 52 Gbps
- DGS-1100-24P/ME : 48Gbps

Max. Forwarding Rate:

- DGS-1100-16/ME: 23.81Mpps

- DGS-1100-18/ME: 26.79Mpps

- DGS-1100-24/ME: 35.71Mpps

- DGS-1100-26/ME: 38.69Mpps

- DGS-1100-24P/ME: 35.71Mpps

Forwarding Mode: Store and Forward

Packet Buffer memory:

- DGS-1100-16/ME: 512Kbits

- DGS-1100-18/ME: 1.5Mbits

- DGS-1100-24/ME: 512Kbits

- DGS-1100-26/ME: 1.5Mbits

- DGS-1100-24P/ME: 512Kbits

Flash Memory: 8M Byte

Port Functions

10/100/1000BaseTX ports compliant with

the following standards:
- IEEE 802.3 compliance
- IEEE 802.3u compliance
- IEEE 802.3ab compliance
- IEEE802.3at (Only DGS-1100-24 Port 1 ~

Port 12)
-Supports Full/half-Duplex operations at

10/100Mbps
-Supports Full-Duplex operation at

1000Mbps
-Supports IEEE 802.3x Flow Control
-Support Auto-Negotiation
-Compliant to IEEE 802.3az Energy

Efficiency Ethernet.

SFP ports compliant with the following

standards:

- IEEE 802.3u compliance

- IEEE 802.3z compliance

Physical & Environment

DGS-1100/ME: AC input, 100~240 VAC,

50/60Hz, internal universal power supply

Acoustic Value:

- DGS-1100-16/ME, 18/ME, 24/ME, 26/ME:

0dB(A) (Fan-less)
- DGS-1100-24P/ME:

44.5 dB(A)

Operation Temperature 0~50°C

Storage Temperature -10~70°C

Operation Humidity: 10%~95% RH

Storage Humidity: 5%~95% RH

Emission (EMI)

Certifications

FCC class A

CE Class A

VCCI Class A

BSMI

CCC

Safety Certifications

CUL, LVD, CB, CCC, BSMI

Features
L2 Features

DGS-1100-16/ME, 24/ME, 24P/ME: 8K

MAC address.

DGS-1100-18/ME, 26/ME: 16K Mac

address

Loopback Detection

Port Mirroring

Link Aggregation

Cable Diagnostics

Spanning Tree

170

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands