D-Link DGS-1100-16/ME Reference Manual Download Page 37

Page: 37 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

DGS-1100-24P/ME:admin#delete time_range dlink

Command : delete time_range dlink

Success.

DGS-1100-24P/ME:admin#

show time_range

Purpose

To display the currently configured access profiles on the Switch.

Syntax

show time_range

Description

The

show time_range

command displays the time range

configuration.

Parameters

None.

Restrictions

None.

Example usage:

To display time range settings on the Switch:

DGS-1100-24P/ME:admin#show time_range

Time Range Information

------------------------------------------

Range Name : dlink

Weekdays : Daily

Start Time : 10:10:00

End Time : 12:10:00

Total Entries :1

DGS-1100-24P/ME:admin#

config telnet auto_logout

Purpose

To configure the auto log out time on the Switch.

Syntax

config telnet auto_logout [2_minutes | 5_minutes | 10_minutes |

15_minutes]

Description

This command is used to configure the auto logout time for idle

connections.

Parameters

2_minutes

- Two minutes to set the automatic logout time

5_minutes -

Five minutes to set the automatic logout time

10_minutes -

Ten minutes to set the automatic logout time

15_minutes -

Fifteen minutes to set the automatic logout time

Restrictions

Only administrator-level users can issue this command.

Example usage:

Two minutes to set the automatic logout time:

DGS-1100-24P/ME:admin#config telnet auto_logout 2_minutes
Command : config telnet auto_logout 2_minutes

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands