D-Link DGS-1100-16/ME Reference Manual Download Page 171

Page: 171 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

Example usage:

To create a link aggregation group:

DGS-1100-24P/ME:admin# create link_aggregation group_id 1
Command : create link_aggregation group_id 1

Success.

DGS-1100-24P/ME:admin#

delete link_aggregation

Purpose

To delete a previously configured link aggregation group.

Syntax

delete link_aggregation group_id <value>

Description

The

delete link_aggregation

group_id command deletes a

previously configured link aggregation group.

Parameters

group_id <value >

− Specifies the group ID. The group number

identifies each of the groups.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To delete link aggregation group:

DGS-1100-24P/ME:admin# delete link_aggregation group_id 1
Command : delete link_aggregation group_id 1

Success.

DGS-1100-24P/ME:admin#

config link_aggregation

Purpose

To configure a previously created link aggregation group.

Syntax

config link_aggregation group_id <value> ports <portlist>

Description

The

config link_aggregation

command configures a link

aggregation group created with the

create link_aggregation

command above.

Parameters

group_id <value>

− Specifies the group ID. The group number

identifies each of the groups.

ports <portlist>

− Specifies a list of ports to belong to the link

aggregation group.

Restrictions

Only administrator-level users can issue this command.
Link aggregation groups may not overlap.

162

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands