D-Link DGS-1100-16/ME Reference Manual Download Page 118

Page: 118 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

DGS-1100-24P/ME:admin#

config mld_snooping multicast_vlan_group

Purpose

To specify that MLD snooping is to be configured for multicast vlan

groups on the Switch.

Syntax

config mld_snooping

multicast_vlan_group <vlan_name 8>

[add | delete] ipv6_range <mcast_range 80>

Description

The

config mld_snooping

multicast_vlan_group

command

specifies an MLD snooping multicast VLAN group on the Switch.

Parameters

<vlan_name 8>

− The name of the VLAN for which

MLD snooping is

to be configured. Up to 8 characters can be used.

[add | delete]

−

Specify whether to add or delete address ranges

defined in the following parameter <mcast_address_range>.

<mcast_range 80>

−

Specify the IPv6 address to be configured with

the MLD snooping multicast VLAN group.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure the mld snooping multicast VLAN:

DGS-1100-24P/ME:admin#config mld_snooping multicast_vlan_group lala

add ipv6_range ffe1::99-ffe1::1:33
Command : config mld_snooping multicast_vlan_group lala add

ipv6_range ffe1::99-ffe1::1:33

Success.

DGS-1100-24P/ME:admin#

enable mld_snooping multicast_vlan

Purpose

To enable MLD snooping multicast VLAN on the Switch.

Syntax

enable mld_snooping multicast_vlan

Description

The

enable mld_snooping

multicast_vlan

command enables MLD

snooping multicast VLAN on the Switch.
MLD snooping and MLD snooping multicast VLAN will have different

behavior in the same packet. If both are enabled at the same time,

only MLD snooping will work.

Parameters

None.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To enable MLD snooping multicast VLAN on the Switch:

DGS-1100-24P/ME:admin#enable mld_snooping multicast_vlan
Command : enable mld_snooping multicast_vlan

109

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands