D-Link DGS-1100-16/ME Reference Manual Download Page 65

Page: 65 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

Command: disable syslog

Success.

DGS-1100-24P/ME:admin#

show syslog

Purpose

To display the system log global setting.

Syntax

show syslog

Description

The

show syslog

command used to display the syslog protocol

global state.

Parameters

None.

Restrictions

None.

Example usage:

To display the syslog function on the Switch:

DGS-1100-24P/ME:admin#show syslog
Command : show syslog

Syslog Global State : Enabled

DGS-1100-24P/ME:admin#

config syslog host

Purpose

To configure the syslog protocol to send system log data to a remote

host.

Syntax

config syslog host [severity [informational | warning | all] |

local7] | state [enable | disable] | udp_port

[<udp_port_number>] | ipaddress <ipaddr>]]

Description

The

config syslog host

command configures the syslog protocol to

send system log information to a remote host.

Parameters

severity

−

The message severity level indicator. These are

described in the following table (Bold font indicates that the

corresponding severity level is currently supported on the Switch):

Numerical Severity

Code

0            Emergency: system is unusable
1            Alert: action must be taken immediately
2            Critical: critical conditions
3            Error: error conditions

4 Warning: warning conditions

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands