D-Link DGS-1100-16/ME Reference Manual Download Page 46

Page: 46 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

NETWORK MANAGEMENT (SNMP) COMMANDS

The Switch supports the Simple Network Management Protocol (SNMP) versions 1 and 2c. Users can

specify which version of the SNMP host wants to use to get the trap from the Switch. The following table

lists the security features of the three SNMP versions:
SNMP Version

Authentication Method

Description

Community String

Community String is used for authentication -

NoAuthNoPriv

v2c

Community String

Community String is used for authentication -

NoAuthNoPriv

The Network Management commands in the Command Line Interface (CLI) are listed (along with the

appropriate parameters) in the following table.

Command

Parameter

create snmp community

<string 16> [read_only | read_write]

delete snmp community

show snmp community

create snmp host

delete snmp host

show snmp host

enable snmp traps

disable snmp traps

show snmp traps

enable snmp

authenticate_traps

disable snmp

authenticate_traps

config snmp

system_location

config snmp

system_name

config snmp

system_contact

config snmp

linkup_traps

[enable | disable]

config snmp

linkdown_traps

[enable | disable]

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands