D-Link DGS-1100-16/ME Reference Manual Download Page 16

Page: 16 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

HARDWARE INSTALLATION

This chapter provides unpacking and installation information for the D-Link Switch.

Step 1: Unpacking

Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User

Manual to make sure all items are present and undamaged. If any item is missing or damaged, please contact

your local D-Link reseller for replacement.

Packing contents of DGS-1100/ME

•

One D-Link DGS-1100/ME Series Switch

•

One AC power cord

•

Four rubber feet

•

Screws and two mounting brackets

•

One Multi-lingual Getting Started Guide

•

One CD with User Manual

If any item are found missing or damaged, please contact the local reseller for replacement.

Step 2: Switch Installation

For safe switch installation and operation, it is recommended that you:

•

Visually inspect the power cord to see that it is secured fully to the AC power connector.

•

Make sure that there is proper heat dissipation and adequate ventilation around the switch.

•

Do not place heavy objects on the switch.

Desktop or Shelf Installation

When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached on

the bottom, at each corner of the device’s base. Allow enough ventilation space between the device and the

objects around it.

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands