D-Link DGS-1100-16/ME Reference Manual Download Page 141

Page: 141 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

Example usage:

To configure STP trap settings

DGS-1100-24P/ME:admin#config stp trap new_root enable
Command : config stp trap new_root enable

Success.

DGS-1100-24P/ME:admin#

config stp version

Purpose

To set the STP version used by the switch.

Syntax

config stp version [rstp | stp]

Description

The

config stp version

command sets the STP version used by the

switch.

Parameters

rstp –

Rapid spanning tree protocol.

stp –

Spanning tree protocol.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To set STP version to RSTP

DGS-1100-24P/ME:admin#config stp version rstp
Command : config stp version rstp

Success.

DGS-1100-24P/ME:admin#

enable stp

Purpose

To enable STP support of the switch.

Syntax

enable stp

Description

The

enable stp

command enables STP support of the switch.

Note

: If Spanning Tree protocol is used, loopback detection will not

be available. If Loopback Detection is enabled, the Spanning Tree

protocol will not be available.

Parameters

None.

Restrictions

Only administrator-level users can issue this command.

132

Summary of Contents for DGS-1100-16/ME






















































































































































































Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands

D-Link DGS-1100-16/ME, Reference Manual

Search results

Summary of Contents for DGS-1100-16/ME

Reviews:

Related manuals for DGS-1100-16/ME

Brands by name

Popular brands