DES-1228/ME Layer 2 Metro Ethernet Switch CLI Reference Manual
170
22
A
CCESS
C
ONTROL
L
IST
(ACL)
C
OMMANDS
The DES-1228/ME implements Access Control Lists that enable the Switch to deny network access to specific devices or device
groups based on IP settings and MAC address.
The access profile commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.
Command
Parameters
create access_profile
[ ethernet { vlan | source_mac <macmask> | destination_mac <macmask> | 802.1p |
ethernet_type }(1) | ip { vlan | source_ip_mask <netmask> | destination_ip_mask
<netmask> | dscp | [ icmp | igmp | tcp {src_port_mask <hex 0x0-0xffff> | dst_port_mask
<hex 0x0-0xffff> | flag_mask [ all | {urg | ack | psh | rst | syn | fin}(1)]} | udp {src_port_mask
<hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} | protocol_id_mask <hex 0x0-0xff>]}(1)]
profile_id <value 1-256>
delete access_profile
[profile_id <value 1-256> | all]
config access_profile
profile_id <value 1-256> [ add access_id [ auto_assign | <value 1-65535> ] [ ethernet {
vlan <vlan_name 32> | source_mac <macaddr> | destination_mac <macaddr> | 802.1p
<value 0-7> | ethernet_type <hex 0x0-0xffff> }(1) | ip { vlan <vlan_name 32> | source_ip
<ipaddr> | destination_ip <ipaddr> | dscp <value 0-63> | [ icmp | igmp | tcp {src_port
<value 0-65535> | dst_port <value 0-65535> | urg | ack | psh | rst | syn | fin } | udp
{src_port <value 0-65535> | dst_port <value 0-65535>} | protocol_id <value 0 - 255> ]}(1)]
port [<portlist> | all ] [ permit{ priority <value 0-7> | replace_priority_with <value 0-7>|
rx_rate [ no_limit |<value 64-1024000>]}|deny|mirror ] | delete access_id <value 1-65535>
]
show access_profile
profile_id <value 1-256>
enable
cpu_interface_filtering
disable
cpu_interface_filtering
create cpu
access_profile profile_id
<value 1-3> [ ethernet { vlan | source_mac <macmask> | destination_mac <macmask> |
802.1p | ethernet_type} (1) | ip { vlan | source_ip_mask <netmask> |
destination_ip_mask <netmask> | dscp | [ icmp { type | code } | igmp { type } | tcp
{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff> | flag_mask [ all | {urg |
ack | psh | rst | syn | fin}(1)] } | udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex
0x0-0xffff>} | protocol_id_mask <hex 0x0-0xff> {user_define <hex 0x0-0xffffffff>}]}(1)]
delete cpu
access_profile
profile_id <value 1-3>
config cpu
access_profile profile_id
<value 1-3> [ add access_id <value 1-5> [ ethernet { vlan <vlan_name 32> | source_mac
<macaddr> | destination_mac <macaddr> | 802.1p <value 0-7> | ethernet_type <hex 0x0-
0xffff> }(1) | ip { vlan <vlan_name 32> | source_ip <ipaddr> | destination_ip <ipaddr> |
dscp <value 0-63> | [ icmp {type <value 0-255> | code <value 0-255>} | igmp {type <value
0-255>} | tcp {src_port <value 0-65535> | dst_port <value 0-65535> | urg | ack | psh |
rst | syn | fin } | udp {src_port <value 0-65535> | dst_port <value 0-65535>} | protocol_id
<value 0 - 255> {user_define <hex 0x0-0xffffffff>}]}(1)] port [<portlist> | all ][ permit | deny ]
| delete access_id <value 1-5> ]
show cpu access_profile
profile_id <value 1-3>
Access profiles allow users to establish criteria to determine whether or not the Switch will forward packets based on the
information contained in each packet’s header.
Creating an access profile is divided into two basic parts. First, an access profile must be created using the
create access_profile
command. For example, if users want to deny all traffic to the subnet 10.42.73.0 to 10.42.73.255, users must first
create
an
access profile that instructs the Switch to examine all of the relevant fields of each frame.
First create an access profile that uses IP addresses as the criteria for examination:
