CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 19

Page: 19 / 132

CTC EcoZenith i360

5.7.1

5.7.2

5.7

Install pipes to and from the heat pump

Heat pump

5.7.1

Install pipe to the heat pump with solenoid fi lter ball valve.

5.7.2

Install pipes from heat pump.

Install any adjustable by-pass coupling past the heat pump. (*a by-pass

coupling is only used for electric operation without a heat pump).

Low Model

High Model

5.7.1
to heat pump solenoid
fi lter ball valve with
support sleeves fi tted,
see instructions in
packaging.
Drain valve is mounted
for high model.

* without a heat pump, to

and from heat pump must
be connected.

CTC EcoZenith i360 is only approved for installation together with CTC Heat pumps.
See the recommended systems at the start of the installation instructions.

5.7.2
from heat pump.

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands