CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 117

Page: 117 / 132

117

CTC EcoZenith i360

12.12.1.5 External test (Diff Thermostat/

EHS/External boiler)

Pump (G46)

Off (On/Off)

Function test of charge pump for EHS.

Mixing valve (Y41)

Close ( - /Close/Open)

Function test of mixing valve for EHS.

Mixing valve (Y42)

Close ( - /Close/Open)

Function test of mixing valve for External Boiler.

Ext. Boiler

Off (On/Off)

Function test of external boiler.

Temperatures

EHS-tank ºC (B47)

0 ºC

Shows temperature value on sensor in EHS-tank.

Diff thermostat ºC (B46)

0 ºC

Shows temperature value on sensor for diff thermostat

tank.

Boiler temp (B9)

0 ºC

Shows temperature value on sensor in external boiler.

12.12.1.6 Test DHW

Tap water pump (G5)

0% (0...100)

Function test of the tap water pump for hot water.

DHW circulation pump (G40)

Off (On/Off)

Test of hot water circulation pump.

Sensor

DHW ºC (B25)

0 ºC

Displays current hot tap water temperature.

Flow sensor (B102)

Off (On/Off)

Shows whether there is a flow in the DHW pipe.

Menu "Installer/Service/Diff thermostat function".

Menu "Installer/Service/Test DHW".

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands