CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 97

Page: 97 / 132

CTC EcoZenith i360

Tariff ext. boiler

No (Yes/No)

This menu bar is displayed if an "Input" for remote

control is defined for the "Tariff EL" function in the

"Installer/Define/Remote Control" menu.

"Yes" means the function can be activated via remote

control.

Read more in the "Installer/Define/Remote Control/Tariff

EL" chapter.

Ext. boiler diff ºC

3 (Off, 1...15)

Compensation set point for External Boiler is set these

many degrees above the set point for “Primary Flow

HS1”, or “DHW,” or “Pool”. This is in addition to the

compensation made for the loss in degree minutes.

Ext. boiler schedule

This menu bar is displayed if a "Schedule" is defined for

the "Tariff EL" function in the "Installer/Define/Remote

Control" menu.

For more information, refer to:

• chapter "Weekly Program" for schedule setting.

• section "Def. Remote Control" in the "Installer /

Define" chapter for defining the remote control
function.

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands