CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 69

Page: 69 / 132

CTC EcoZenith i360

When holiday is enabled, hot water production is stopped. The
"Temporary extra DHW" feature is also stopped.

12.4.4

Holiday

You use this option to set the number of days that you

want the set temperature to be consecutively reduced.

For example, if you want to go on holiday.

The value by which the temperature is lowered during

the period is set in one of the following menus:

Room sensor installed

"Installer/Settings/Heating circuit/

Room temperature lowered holiday °C".

Room sensor not installed

"Installer/Settings/Heating circuit/

Primary flow lowered holiday °C".

Holiday reduction is enabled from the time of setting

(press the plus (+) symbol).

Up to 300 days can be set.

When both "Night Reduction" and
"Holiday Reduction" are in use,
"Holiday Reduction" supersedes
"Night Reduction".

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands