CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 91

Page: 91 / 132

CTC EcoZenith i360

Tariff EL schedule

This menu bar is displayed if a "Schedule" is defined for

the "Tariff EL" function in the "Installer/Define/Remote

Control" menu.

For more information, refer to:

• chapter "Weekly Program" for schedule setting.

• section "Def. Remote Control" in the

"Installer / Define" chapter for defining the remote
control function.

SmartGrid block immersion

No (Yes/No)

For this menu to be displayed, define a remote control

input for both SmartGrid A and SmartGrid B.

"Yes" means the function can be activated via remote

control.

Read more in the "Installer/Define/Remote Control"

chapter.

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands