CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 99

Page: 99 / 132

CTC EcoZenith i360

Menu: "Installer/Settings/Communication".

Menu: "Installer/Settings/Communication/BMS".

Menu: "Installer/Settings/Communication/Internet".

Menu: "Installer/Settings/Communication/MyUplink".

For more information about
connecting an ethernet cable, refer
to the "Installation, Communication"
chapter of this manual.

12.10.9 Settings Communication

Settings can be made here to control the product with a

controlling system.

12.10.9.1 Ethernet

DHCP

Yes (Yes/No)

"Yes" enables automatic connection to the network.

If "No", custom router settings (IP address, Netmask

and Gateway) as well as DNR setting must be made.

Auto DNR

Yes (Yes/No)

If "Yes", default DNR server settings are used. If "No",

custom DNR settings must be made.

SNTP server

Option for custom SNTP server settings.

Connection speed

100mbit

Connection speed is specified here.

The factory-set connection speed is 10 Mbps.

12.10.9.2 BMS

MB address

1 (1...255)

Adjustable "1-255".

Baud rate

9600 (9600/19200)

Possible settings: "9600" or "19200".

Parity

Even (Even/Odd/None)

Possible settings: "Even", "Odd" or "None".

Stop bit

1 (1/2)

Possible settings: 1 or 2.

Modbus TCP Port

502 (1...32767)

This menu bar is displayed if "Modbus TCP" is defined

in the "Ethernet" row in the "Installer/Define/Remote

Control" menu.

12.10.9.3 MyUplink

This menu is used for pairing with the MyUplink app. To

request a connection code/token, press "Get token",

confirm with "OK".

The menu bar is only clickable if the display is

connected to the server.

The following values are displayed:

• ”Serial”: Serial number

• "Token": Token/connection code

These must be entered in MyUplink when pairing.

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands