CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 90

Page: 90 / 132

CTC EcoZenith i360

Menu: "Installer/Settings/Set Electric heater.

12.10.3 Settings Electric heater

Max el. heater kW

9.1 (0.0...9.1)

Here you select the power that the electric heater is

permitted to provide.

The setting range varies, see "Electrical data" in

the chapter "Technical data". For language choices

"German" and "French" the max electric power is

factory set at 0.0 kW.

Max el. heater DHW kW

9.1 (0.0...9.1)

The power the electric heater is allowed to deliver for

hot water charging is selected here.

The setting range varies, see "Electrical data" in

the chapter "Technical data". For language choices

"German" and "French" the max electric power is

factory set at 0.0 kW.

Start at degree minute

-500 (-900...-30)

This menu is used to define at how many degree

minutes the electric heater should start.

Diff step, degree minute

-50 (-300...-20)

This menu is used to define the difference in degree

minutes between the start and stop conditions for the

electric heater. If the electric heater is started at -500

degree minutes, it will be stopped at -450 degree

minutes (for a setting of -50).

Main fuse A

20 (10...90)

The property’s main fuse size is set here. This setting

and the fitted current sensors ensure the fuses are

protected when using appliances which generate

temporary power peaks, for example, cookers, ovens,

engine heaters, etc. The product temporarily reduces

power drawn where this type of equipment is being

used.

Conv. factor curr. sensor

1 (1...10)

This menu is used to specific the conversion factor

the current sensor should use. This setting is only

performed if the connection has been installed for a

current sensor for higher currents.

Example: User (set) value 2 => 16 A will be 32 A.

Tariff EL

No (No/Yes)

This menu bar is displayed if an "Input" for remote

control is defined for the "Tariff EL" function in the

"Installer/Define/Remote Control" menu.

"Yes" means the function can be activated via remote

control.

Read more in the "Installer/Define/Remote Control/Tariff

EL" chapter.

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands