CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 118

Page: 118 / 132

118

CTC EcoZenith i360

12.12.2 Alarm log

In the alarm log, up to 500 alarms can be displayed at

the same time.

An alarm which reoccurs within an hour is ignored so as

not to fill up the log.

Click an alarm row to see more information about an

alarm.

If it is a "sensor alarm", a sensor value will be displayed

at the bottom of the page from when the alarm was

triggered for further troubleshooting.

For alarms related to the heat pump, values can

be displayed from sensors for pressure (HP, LP),

temperature (SH-Superheating) and current (I).

12.12.3 Alarm dumps

Export the alarms displayed in the alarm log to a USB

drive. A dump can consist of one or more alarms as

well as specific values before and after the alarm was

triggered.

Menu: "Installer/Service/Alarm logs".

Menu: "Installer/Service/Alarm Dumps".

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands