CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 49

Page: 49 / 132

CTC EcoZenith i360

In order to define and enable connection to the network and app, an ethernet cable

must be connected as described below.

1. Pull out the magnetic strip. It is secured with

magnets. If difficult to remove, use a small screwdriver in

the notch along the top edge.

2. Open the ferrite from the packaging, clamp around

the ethernet cable with the connector.

3. Connect the ethernet cable.

4. Route the ethernet cable through any hole in the top

cover, remove rubber grommet if necessary.

5. Connect ethernet cable to network port or router.

To permit and define connectivity, refer to the

"Communication" section in the "Installer/Define"

chapter.

7.1

Install ethernet cable

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands