CTC Union EcoZenith i350 L 1x230V Installation And Maintenance Manual Download Page 114

Page: 114 / 132

114

CTC EcoZenith i360

12.11.9

Def. SMS

Activate

No (Yes/No)

If "Yes" is selected, the menus below are displayed:

Level of signal

The signal strength of the reception is shown here.

Phone Number 1

The first activated phone number is shown here.

Phone Number 2

The second activated phone number is shown here.

Hardware Version

The hardware version of the SMS accessory is shown

here.

Software version

The software version of the SMS accessory is shown

here.

NB: For more information about the SMS function,

refer to the "Installation and Maintenance Manual" for

CTC SMS.

12.11.10 Def. SmartControl

SmartControl is a separate series of wireless

accessories.

SmartControl

No (Yes/No)

If "Yes" is selected, SmartControl accessories can be

connected to the heating circuit. Refer to the connection

procedure in the separate SmartControl Accessories

manual.

12.11.11 Def. Current sensor

Current sensor

Yes (Yes/No)

Select "Yes" is current sensors are to be connected to

the system.

For more information, refer to the "Current Sensors"

section in the "Installer/Settings" chapter.

Menu: "Installer/Define/SmartControl".

Menu: "Installer / Define / SMS".

Summary of Contents for EcoZenith i350 L 1x230V





































































































































Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands

CTC Union EcoZenith i350 L 1x230V, Installation And Maintenance Manual

Search results

Summary of Contents for EcoZenith i350 L 1x230V

Reviews:

Related manuals for EcoZenith i350 L 1x230V

Brands by name

Popular brands