![background image](http://html1.mh-extra.com/html/club-car/ds-villager-4/ds-villager-4_maintenance-and-service-manual_2626710346.webp)
18
Test Procedures
GASOLINE VEHICLE - TROUBLESHOOTING
AND ELECTRICAL SYSTEM
2m
20
m
200
m
2k
200
200
200
200
20
2
200
m
500
20k
200k
2000
k
1000
OFF
WAVETEK
5XL
V
V
V
A
!
!
COM
200nA
MAX
1000 ---
750V
FUSED
1
–M
2
+M
1
1. 200 Ohm Setting
1337
Figure 18-3
Key Switch Test – Engine Kill Circuit
6.
Put the red (+) probe on the (+M) terminal.
7.
Put the black (–) probe on the (–M) terminal.
8.
With the key switch OFF, the reading should be continuity.
8.1.
If there is no continuity, replace the key switch.
9.
With the key switch ON, the reading should be no continuity.
9.1.
If there is continuity, replace the key switch.
10.
Connect the wires to the key switch. Make sure wires are connected correctly and are tight. If they are not,
rewire or tighten as necessary.
11.
Install the instrument panel. See Instrument Panel Installation.
TEST PROCEDURE 6 – Throttle Position Sensor (TPS)
The throttle position sensor performs the function of two limit switches: the accelerator pedal limit switch and the kill
limit switch. This sensor is sealed and is not to be repaired or replaced. If sensor is determined to need replacing
through test procedures found in this manual, the accelerator pedal assembly must be replaced. See Accelerator
Pedal Removal. The sensor is joined to the main wire harness through a six-pin connector. Tests for the sensor
are found in the following two procedures.
Accelerator Pedal Limit Switch Function
See General Warnings on page 1-2.
The green and orange wires connect to the accelerator pedal limit switch function of the throttle position sensor. This is
the normally open (NO) portion of the circuit used to energize the starter solenoid.
NOTE:
Keep the battery connected while performing this test procedure.
1.
Set the Maintenance/Operate switch to MAINTENANCE.
2.
Disconnect the spark plug wire.
3.
Disconnect gray 18-pin connector from ECU.
4.
Set the multimeter to the diode test function.
5.
Attach the red (+) lead to the orange wire at the starter solenoid.
6.
Attach the black (-) lead to the green wire at the limit switch located on the Forward/Neutral/Reverse control
(FNR).
See following NOTE.
Page 18-12
2020 Precedent,Villager 2 and 4 Maintenance and Service Manual
Summary of Contents for DS Villager 4
