ELECTRIC VEHICLE - ELECTRICAL
COMPONENTS
Solenoid
13
5.
Place the Tow/Run switch in the TOW position and connect the batteries.
See Connect the Batteries – Electric
6.
Place the Tow/Run switch in the RUN position.
7.
If vehicle is equipped with the Guardian SVC system, perform the following additional steps for proper setup.
7.1.
Connect an CDT to the CDT port on the vehicle.
7.2.
Select
Program, Settings, Control Mode
and set the value to 1.
7.3.
Select
Program, Settings, Anti Tamper
and set the value to 0.
7.4.
Select
Program, Vehicle ID, Vehicle S/N
and enter the last six digits of the vehicle serial number.
NOTE:
The speed for scrolling values may be increased by utilizing the bookmark keys (yellow buttons) in combination
with the data inc/dec key (+/-).
7.5.
Select
Program, Vehicle ID, Vehicle Decal
and enter the number on the Vehicle Number Decal.
7.6.
Select
Program, Vehicle ID, Vehicle Date of Manufacture
and enter the number on the model year and
week from the vehicle serial number.
7.7.
Select
Information, Software Version
and verify the value is 13 or higher. If not, contact a Club Car
Technical Representative.
7.8.
Place the Tow/Run switch in the TOW position for 30 seconds. Then return it to RUN.
8.
Inspect the vehicle for proper operation.
WARNING
• Make sure that the vehicle operates in the forward direction when the Forward/Reverse switch is
in the FORWARD position.
• Make sure that the vehicle operates in the reverse direction when the Forward/Reverse switch is in the
REVERSE position. The reverse buzzer will sound as a warning when the Forward/Reverse switch
is in REVERSE.
• Make sure that the vehicle does not operate when the Forward/Reverse switch is in the NEUTRAL
position.
SOLENOID
See General Warnings on page 1-2.
The solenoid is located on the rear side of the electronics module.
TESTING THE SOLENOID
See Test Procedure 7 – Solenoid Activating Coil on page 12-20 and Test Procedure 9 – Solenoid Continuity on
page 12-21.
SOLENOID REMOVAL
1.
Disconnect the batteries and discharge the controller (1).
See Disconnect the Batteries – Electric Vehicles
2.
Remove the electronics module cover (8) to access the solenoid (4).
See Electronics Module Cover Removal
2020 Precedent,Villager 2 and 4 Maintenance and Service Manual
Page 13-13
Summary of Contents for DS Villager 4
