Christie CP2000-X, User Manual

Page: 149 / 164

ASCII MESSAGES
CP2000-X User Manual
B-3
020-100031-01 Rev. 1 (03-3009)
Function Code / Examples Description and Parameters
(LPI 12345) The light output level chosen for LiteLOC. Same intensity
for every channel requires LPB (Lamp Per Button) set to
“OFF”.
NOTE: Specify desired channel with “S”. If no “S” parameter is included,
the LPI setting will apply to the current channel when the “Lamp Per
Channel” checkbox is enabled, and to all channels when the checkbox is
cleared.
(LPI?) What is the current LiteLOC setting for this channel?
(LPI?s101) What is the LiteLOC setting for Channel #1?
(LP1!12345) The current LiteLOC setting is 12345
Lamp Limit (LPL)
(LPL 750)
(LPL?)
(LPL!750)
The #hours that a lamp can be used before a warning
message appears. Range=0-5000 hours.
LampLOC Module (LLM)
(LLM000 000 0158)
P1 = Type of motor movement
0=move to a specific new position
(see P2 and P3)
1=calibrate motors
2=Do AUTO lamp alignment (LampLOC)
P2 = Which motor…x(0), y(1), or z(2)
P3 = Destination / new motor position (-200 up to +200)
Lamp Message Enable (LME)
(LME 0)
(LME 1)
0 = No lamp message will appear when lamp limit expires
1 = Lamp message will appear when lamp limit expires
Lamp Mode (LPM)
(LPM 2)
(LPM?)
(LPM! 3)
2 = Constant power
3 = Constant light intensity
NOTE: Specify desired channel with “S”. If no “S” parameter is included,
the LPM setting will apply to the current channel when the “Lamp Per
Channel” checkbox is enabled, and to all channels when the checkbox is
cleared.
Lamp Per Button (LPB)
(LPB O)
(LPB?)
(LPB! 1)
0 = Off; Lamp settings will be the same for all channels.
1 = On; Lamp settings will vary according to channel.
NOTE: This setting determines whether lamp mode, power and intensity
are the SAME for every channel (i.e., global) or DIFFERENT for each.
Lamp Power (LPP)
(LPP 2000)
(LPP?)
(LPP!2000)
Specific power setting (#watts) for driving the lamp.
Range = depends on the installed lamp
NOTE: Specify desired channel with “S”. If no “S” parameter is included,
the LPP setting will apply to the current channel when the “Lamp Per
Channel” checkbox is enabled, and to all channels when the checkbox is
cleared.
Measured Color Gamut (MCG)
(MCG “OnSite”)
Use OnSite MCGD as the reference point for color proc.
(MCG?) What MCGD is currently in use?
(MCG! OnSite) Reply indicating the OnSite MCGD is in use
Ping (PNG)
(PNG?)
Request for projector type and current s/w version
(PNG! 032 001 002) Reply indicating cinema projector present (32), and its
current version of software is v1.2
P1 = 32 (always—indicates a cinema projector)
P2 = Major version 0-99
P3 = Minor version 0-99
Power (PWR)
(PWR 0)
(PWR 1)
(PWR! 000)
(PWR! 001)
Turn the projector off or on (0=off, 1=on). Examples:
Turn the projector (lamp) off
Turn the projector (lamp) on
The projector (lamp) is off
The projector (lamp) is on
Processing Mode (PRM)
(PRM 0)
Current processing of incoming source data, where 0=