Christie CP2000-X, User Manual

Page: 104 / 164

CINEMA OPERATION
4-2
CP2000-X User Manual
020-100031-01 Rev. 1 (03-2009)
Table 4.1. Compatible Formats for Cinema
NOTE:
ALL SOURCES SHOWN ARE 10-BIT 4:2:2UNPACKED UNLESS OTHERWISE NOTED
Source Standard Orig. Format Vert. Freq. Scan Type Display Format (Progressive)
SMPTE 274M-1998
(NOTE: USES 1125 TOTAL LINES PER FRAME)
SMPTE 274
1920 x 1080 60 Hz * Interlaced 1920 x 1080; 24 Hz
1920 x 1080 59.94 Hz * Interlaced 1920 x 1080; 23.98
1920 x 1080 50 Hz ** Interlaced 1920 x 1080; 25 Hz
1920 x 1080 30 Hz Progressive 1920 x 1080; 30 Hz
1920 x 1080 29.97 Hz Progressive 1920 x 1080; 29.97 Hz
1920 x 1080 25 Hz Progressive 1920 x 1080; 25 Hz
1920 x 1080 24 Hz Progressive 1920 x 1080; 24 Hz
1920 x 1080 23.98 Hz Progressive 1920 x 1080; 23.98 Hz
SMPTE RP211-2000
SMPTE RP 211
1920 x 1080 30 Hz Prog. Segmented Frame 1920 x 1080; 30 Hz
1920 x 1080 29.97 Hz Prog. Segmented Frame 1920 x 1080; 29.97 Hz
1920 x 1080 25 Hz Prog. Segmented Frame 1920 x 1080; 25 Hz
1920 x 1080 24 Hz Prog. Segmented Frame 1920 x 1080; 24 Hz
1920 x 1080 23.98 Hz Prog. Segmented Frame 1920 x 1080; 24 Hz
SMPTE 295M-1997
(NOTE: USES 1250 TOTAL LINES PER FRAME)
SMPTE 295M 1920 x 1080 50 Hz ** Interlaced 1920 x 1080; 25 Hz
SMPTE 296M-2001
SMPTE 296M
1280 x 720 60 Hz Progressive
] ] ]
1673 x 941; 60 Hz; Progressive
1280 x 720 59.94 Hz Progressive
] ] ]
1673 x 941; 59.94 Hz; Progressive
1280 x 720 50 Hz Progressive 1920 x 1080; 50 Hz
1280 x 720 30 Hz Progressive 1920 x 1080; 30 Hz
1280 x 720 29.97 Hz Progressive 1920 x 1080; 29.97 Hz
1280 x 720 25 Hz Progressive 1920 x 1080; 25 Hz
1280 x 720 24 Hz Progressive 1920 x 1080; 24 Hz
1280 x 720 23.98 Hz Progressive 1920 x 1080; 23.98 Hz
SMPTE 260M-1999
(NOTE: THIS STANDARD DOES NOT OFFICIALLY SUPPORT 60/M)
SMPTE 260M
1920 x 1035 60 Hz * Interlaced 1920 x 1080; 24 Hz
1920 x 1035 59.94 Hz * Interlaced 1920 x 1080; 23.98 Hz
SMPTE 372M-2001 DUAL-LINK
All SMPTE 292m-1998 single-link formats (see above) are available as 12-bit 4 :4 :4 dual link, with the same performance/format.
 M = 1.001

* Signal must include 3:2 pull-down encoding and Ancillary Time code information.
 * * Signal must include 2:2 pull-down encoding, and assumes field one (1) dominance. Same as Prog. Segmented Frame.
 * * * Image will be centered vertically on screen (default).
Keep in mind that the projector will attempt to automatically adapt to any incoming
data format that does not exceed either the bandwidth of the system or the frame rate
limitations, thus formats beyond those shown above may be compatible
The two standard types of cinema displays—flat and scope—differ in their width-to-
height aspect ratio as shown below:
Figure 4.2. Standard Cinema Formats
Achieving either of these displays from a wide variety of incoming source material
depends on proper settings in the projector as well as certain theatre conditions.
4.2 Image Formats