manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 95 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 95

3 - CONTROLS AND INSTRUMENTS

Setting trip screens

Highlight the trip screen you wish to set. (Capacity can
be set in United States gallons, Imperial gallons, or metric
liters when setting measurement preferences).

Press the enter/confirm switch to reset to the desired trip
screen.

The trip screen will indicate a reset message. At this
screen, press the enter/confirm switch to clear the num-
bers and reset the trip information. The current date and
time will display automatically. The hours, fuel consump-
tion, and fuel used per hour will reset and revert to zero.

Press the escape switch to return to the main driving
screen and lock settings into memory. The screen will
begin to record time and fuel usage immediately.

RCPH10WHL353AAH

10

3-47

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments