manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 46 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 46

2 - SAFETY INFORMATION

DANGER — Run over hazard

RAIL13DOX1617AA

34

This DANGER safety sign is located on both sides of
the machine just ahead of the engine front access lower
doors.
DANGER — Run over hazard keep clear of machine.
Failure to comply will result in death or serious injury.
English safety sign number: 47543424
French safety sign number: 87719507
Spanish safety sign number: 87719507

47543424

35

WARNING — Hot surface hazard

RAIL13DOZ1604AA

36

This WARNING safety sign is located on both sides
of the machine just ahead of the engine front access
doors, and on top of the hood near the exhaust stack.
On bull dozer blade equipped machines, this safety
sign is located only on top of the hood near the exhaust
stack.
WARNING — Hot surface hazard stay clear. Failure to
comply could result in death or serious injury.
English safety sign number: 418242A3
French safety sign number: 87415865
Spanish safety sign number: 87415865

418242A3

37

2-24

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments