manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 131 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 131

5 - TRANSPORT OPERATIONS

Transporting by truck or trailer

WARNING

Driving hazard!
Know all rules, regulations, laws, and required safety equipment for transporting or operating this ma-
chine on a road or highway. See your dealer to obtain a rotating beacon, backup alarm, Slow Moving
Vehicle (SMV) emblem, and other safety equipment.
Failure to comply could result in death or serious injury.

W0154A

WARNING

Transport hazard!
The machine can slip or fall from a ramp or trailer. Make sure the ramp and trailer are not slippery.
Remove all oil, grease, ice, etc. Move the machine on or off the trailer with machine centered on the
trailer or ramp.
Failure to comply could result in death or serious injury.

W0152A

Transporting the machine by truck or trailer

NOTICE:

Make certain the truck and trailer are adequate for the machine. The truck, trailer, and machine must be

equipped with the correct safety equipment for transport. Wide load escorts may be required for some machines.
Remove all dirt, mud, snow, ice, oil, or grease from the trailer and ramp before loading or unloading the machine.

Make sure you know the safety rules and regulations before transporting the machine. You must know the rules or
laws for transportation and safety that are used in each area that you will be in. Make sure that the truck and machine
are equipped with the correct safety equipment. Use care when loading a machine.

1. Put a block on both sides of the trailer wheels.

2. Move the crawler slowly onto the trailer. Place the

direction control lever in the neutral position.

3. Lower the blade and ripper, if equipped, to the trailer.

4. Engage the parking brake.

5. Stop the engine, remove the key, and lock all access

doors.

RCIL10CWL015AAL

1

5-9

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments