manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 64 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 64

3 - CONTROLS AND INSTRUMENTS

Engine coolant temperature gauge

The engine coolant temperature gauge

(1)

indicates the coolant temperature of

the engine. Normal operating temperature
is in the green zone. When the engine
coolant temperature increases the gauge
will move into the yellow zone, and the
warning alarm sounds for three seconds.
The caution master indicator turns yellow. If
the temperature continues to increase, the
gauge moves into the red zone, and the
audible warning alarm sounds continuously.
The stop master indicator turns red. Do not
operate the machine when the temperature
is in the red zone.

RAPH12DOZ0138AA

4

Engine coolant temperature gauge

Gauge indication

Condition

Master

indicator

Gauge

status

Alarm

status

20 - 103 °C

(

68 - 217 °F

)

Coolant temperature is normal

103 - 105 °C

(

217 -

221 °F

)

Coolant temperature is high

Caution
(Yellow)

Solid

1 Second

105 °C

(

221 °F

) and

above

Coolant temperature is very high

Stop (Red)

Solid

Continuous

3-16

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments