manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 118 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 118

4 - OPERATING INSTRUCTIONS

3. The Settings screen will display along with the follow-

ing choices:
Engine
Transmission
Hydraulics
Factory Set

4. Use the down arrow on the up/down switch

(2)

to high-

light “Transmission”. Press the enter switch

(1)

.

RAIL12DOZ0212AA

3

The “Transm.” screen will display.

5. Use the down arrow on the up/down switch

(2)

to high-

light “Steer”.

NOTE:

Moderate (displayed as Modrt) is preset from

the factory.

6. Push the enter switch

(1)

to confirm the selection.

7. Choose and highlight the setting desired: “Smooth”,

“Moderate”, or “Aggressive” to confirm the selection.

8. Press the escape switch

(1)

(the top of the enter/es-

cape switch) to store the choice.

RAIL14DOZ0583AA

4

4-16

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments