manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 56 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 56

3 - CONTROLS AND INSTRUMENTS

Foot controls

Dual function pedal

The dual function pedal can be switched to operate as a deceleration pedal or a transmission control pedal. As a
deceleration pedal, the engine RPM is reduced as the pedal is depressed. As a transmission pedal, the hydraulic
system is de-stroked as the pedal is depressed. The transmission pedal is the default function. These settings are
made through the transmission selection on the multi-function display.

NOTE:

See the multi-function display on page

4-20

for more information.

Transmission pedal

As a transmission pedal, the machine varies the transmis-
sion flow (pump/motor displacement) allowing for inching.
Pushing the pedal completely down will de-stroke the hy-
draulics.

RAIL13DOZ1264AA

1

Deceleration pedal

The deceleration pedal reduces the engine RPM and
slows the machine. Push the deceleration pedal to slow
or stop the machine.

RAIL12DOZ1254AA

2

Use the deceleration pedal to reduce the speed all the
way to zero by de-stroking the ground drive along with
decreasing the engine RPM.

NOTE:

Use the deceleration pedal to control the dozer for

precision work.

47449566

3

3-8

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments