Case 2050M Operator'S Manual Download Page 32 | Manualshive

Page: 32 / 286

Case 2050M Operator'S Manual Download Page 32

2 - SAFETY INFORMATION

Operator's seat belt

WARNING

Roll-over hazard!
Securely fasten the seat belt. Your machine is equipped with a Roll-Over Protective Structure (ROPS)
cab, ROPS canopy, or ROPS frame for your protection. The seat belt can help ensure your safety if it
is properly used and maintained. Never wear a seat belt loosely or with slack in the belt system.
Failure to comply could result in death or serious injury.

W0143A

Seat belt

1. Insert the metal end of the right-hand belt strap into

the latch mechanism on the left-hand side of the seat.

2. Tighten the seat belt by pulling on the loose end of the

right-hand seat belt.

3. Press on the red button on the left-hand side mecha-

nism to unlatch the seat belt.

RCIL10CWL083FAL

1

1. Right-hand belt strap
2. Latch mechanism

2-10

«
...
30
31
32
33
34
...
»

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments