manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 91 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 91

3 - CONTROLS AND INSTRUMENTS

Telematics

SiteWatch™

This machine may be equipped with a telematics system. This is an asset-monitoring system that combines Internet,
cellular, and GPS technologies. A transponder unit is mounted on the equipment that wirelessly communicates with
the user interface CASE CONSTRUCTION

SiteWatch™

at www.casesitewatch.com. Using cellular technology, the

transponder can send equipment data including location, on/off status, usage and production metrics, diagnostic data,
movement alarms, and unauthorized usage to the interface. The system will help cut costs and keep accurate records.
See the furnished guide for operating your telematics system.

NOTE:

The CASE CONSTRUCTION

SiteWatch™

website (www.casesitewatch.com) will not be accessible until

the CASE CONSTRUCTION

SiteWatch™

subscription for this machine is registered by an authorized CASE CON-

STRUCTION dealer. Contact an authorized CASE CONSTRUCTION dealer for details.

3-43

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments