manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 54 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 54

3 - CONTROLS AND INSTRUMENTS

Seat belt

WARNING

Roll-over hazard!
Securely fasten the seat belt. Your machine is equipped with a Roll-Over Protective Structure (ROPS)
cab, ROPS canopy, or ROPS frame for your protection. The seat belt can help ensure your safety if it
is properly used and maintained. Never wear a seat belt loosely or with slack in the belt system.
Failure to comply could result in death or serious injury.

W0143A

Fastening the seat belt

Pull the right-hand belt from the seat belt retractor. Fasten
the metal belt end into the left-hand buckle.

RCIL10CWL037AAL

1

Unfastening the seat belt

Press the red button on the left-hand seat belt mechanism
to release the seat belt.

RCIL10CWL083FAL

2

3-6

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments