manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 94 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 94

3 - CONTROLS AND INSTRUMENTS

Push the down switch again to display the Info 3 screen.
This screen displays the voltage and hydraulic oil temper-
ature.

RAIL12DOZ0822AA

7

Trip screens

NOTE:

The Trip screens can only be accessed with the

key in the ON position, and the engine OFF.

Press the down switch again and the Trip 1 screen will
display. The LCD provides two trip computers. The trip
screens will display since last reset the total time in hours,
the total fuel, and the average fuel consumption per hour.

RCPH10WHL353AAH

8

By continuing to scroll down, the Trip 2 screen will display.
Trip 1 and Trip 2 screens can be reset independently.

Previous screens can be accessed by using the up arrow
switch.

RCPH10WHL354AAH

9

3-46

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments