manualshive.com logo in svg

Case 2050M, Operator'S Manual, Page: 147 / 286

Share
Download
Case 2050M Operator'S Manual Download Page 147

6 - WORKING OPERATIONS

Track systems

RAIL12DOZ0228FA

1

Track frame

The track frames

(1)

attach to the machine chassis on

each side. All the track components except the drive
sprockets attach to the track frames.

Carrier rollers

The carrier rollers

(2)

mount on the top of the track frames.

The carrier roller supports the track chain between the
drive sprocket and idler. The carrier roller helps main-
tain alignment of the chain between the idler and drive
sprocket.

Track chain

The track chains

(3)

include a number of link assemblies

connected together to form a complete chain. Shoes bolt
to the track chain

(3)

to provide traction for the machine.

Drive sprocket

The drive sprockets

(4)

transmit engine power to the

tracks. The drive sprockets rotate the track chain around
the undercarriage assembly. The drive sprockets

(4)

do

not support the weight of the machine.

Track rollers

The track rollers

(5)

mount to the bottom of the track

frames. These rollers carry the weight of the machine on
the track chains.

Idler

The idler

(6)

carries the track chain around the front of

the track frame. This assembly can slide forward or back
on the track frame against the recoil spring to absorb any
shock loads. These shock loads can be from changes in
the terrain or temporary material buildup on the tracks.

6-11

Summary of Contents for 2050M































































































































































































































































































Reviews:

No comments